Pyro Industries Quest Plus Betriebsanleitung

OUEST A PLUS SE READ 1 ILURE TO TH. CONT, - . . . . . . . Owners Manual Operating Instructions - SAVE THESE INSTRUCTIONS - -HIS ENTIF FOLLOW ACT YO

Operating instructions p Manual Lighting Procedure: If Priming Is Required 1. Fill the hopper with recommended pellet fuel and plug the stove into the

General Operating Considerations Proper Burn Characteristics: The flame in your stove should be bright yellow under normal operation. If the flame be

Thermos tat Installation .* NOTE: ALWAYS DISCONNECT POWER BEFORE PERFORMING THE THERMOSTAT INSTALLATION. To Install A Wall 1. Check the type of th

Routine Cleaning NOTE: STOVE WILL NEED TO BE SHUT OFF AND COOLED ENOUGH TO HANDLE BEFORE ROUTINE CLEANING IS PERFORMED. ALWAYS DISCONNECT POWER BEFORE

Routine Cleaning & Maintenance (cont.) )" EXHAUST DUCTS Inspect the exhaust ducts periodically and clean / when necessary. Fly ash will acc

Stove Installa tion Stove /nsfallafion Checklist Check off each item as you go through your installation. As part of the installation process: It is

Pre-lnstalla tion Assembly #- 1. After removing the packaging from the stove, lift the hopper lid, and remove all pre-packaged items that were shipp

Stove lnstalla tion Assembly Your Whitfield Quest Plus May Be Installed As: A freestanding unit with a pedestal placed on a noncombustible floor pa

Stove Vent Pipe/ln ta ke Installa tion IT IS RECOMMENDED THAT ONLY AN AUTHORIZED DEALER INSTALL YOUR PELLET STOVE. THE FOLLOWING INSTALLATION GUIDEL

Determining Equivalent Pipe Length To determine whether a 3" or 4" exhaust system is required for your installation, review the sample ~nst

Congratulations on the purchase of your Whitfield Quest Plus Pellet Stove! When you purchased your Whitfield stove, you joined the ranks of thousand

Installing Your Freestanding Pellet Stove P STANDARD HORIZONTAL EXHAUST INSTALLATION 1. Locate the proper position for the listed type "L" w

freestand Stove Dimensions / I - Freestand Dimensions Plus or Minus 1/4"

Ins ta//a tion Configurations I NONEOMBUSTISLE Hearth Pad (3/8" Minimum Thickness) 3" Minimum- Between WaN and Pipe C ..::::.. r'... :

lnstalla tion Configurations (Cont'd) Venting Options The Quest Plus may be connected to an existing flue or by installing listed type "L&q

Mobile Home Installa tion . p*. IN ADDITION TO THE STANDARD INSTALLATION INSTRUCTIONS, THE FOLLOWING INSTRUCTIONS MAY BE REQUIRED BY LOCAL, STATE O

Installing Your Insert Pellet Stove INSERT STOVE VENTING A 3" single-wall, stainless steel flexible or rigid exhaust pipe may be used for insert

Insert Stove Dimensions (Figure 24)-Insert Pipe Adapter Connection - (Figure 25)-Front View of Insert Contact your dealer for further assistance or in

Insert Stove Dimensions (cont.) INSERT STOVE VENTING - continued - 24 114" i >: (Figure 27) Back View of hsert

Quest Plus lnsert Exhaust Connection .@ FLEX LINER INSTALLATION WITH COUPLER Coupler Part Number: 13.8201 34 A Flex Liner may be attached to the t

Installing Your Insert Pellet Stove VENTING INTO AN EXISTING CHIMNEY 53 -RAIN CAP f* INSERT STOVE VENTED INTO EXISTING CHIMNEY andlor pipe support The

Table Of Contents Safety Precautions Safety Notice ... 4 Installation Disclaimer ...

Routine Maintenance UNPLUG STOVE BEFORE PERFORMING ANY MAINTENANCE WORK The following areas need to be inspected as part of routine maintenance: Door

APPENDIX A TROUBLE-SHOOTING Unplug Stove Before Performing any Maintenance work Fire burns with a lazy be obstructing the primary air dow gets sooted

APPENDIX A TROUBLE-SHOOTING (CONT'D ...) Unplug Stove Before Performing any Maintenance work lower burn rates) then the high limit snap switch s

APPENDIX A TROUBLE-SHOOTING (CONT'D ...) Unplug Sfove Before Performing any Maintenance work when the start switch is Check to see if your circu

APPENDIX B Solid ,k OPTIONAL ACCESSORIES *C P Hearth Pads Trimmed in solid oak, Whitfield hearth Pads are available in an a array of colors and color

APPENDIX C SHROUD PANEL ACCESS

APPENDIX D WARRANTY THlS WARRANTY IS ISSUED BY PYRO INDUSTRIES, INC. (MANUFACTURER) AND EXTENDS ONLY TO THE ORIGINAL PURCHASER OF THlS PRODUCT. T

APPENDIX E REPLACEMENT PARTS I/ Common To Both Freestand & Insert 132 #I2140213 1 Igniter Re~lacement Kit (if included) I I/ 1 #I7150009 1 scrape

Replacement Parts Freestand & lnsert Replacement Parts Freestanding Only ,' / , , . , I,". ' .. . \ ,, I : I I . ,., . ,- . ,, ,,&a

APPENDIX E REPLACEMENT PARTS INSERT ONLY + I Insert only /I I 56 #I3851078 Top Panel (black) I I ; 57(#13852078 1 Top Panel (brown) 158 #I3854078 T

Table Of Contents (Cont'd) . c Stove lnstallafion Stove Installation Check List ... 14 Pre-Installation Assemb

B Y BYRO INDUSTRIES, IHC. Whitfield Pellet Quest Plus Owners Operation Manual Part Number 17220098 IR 0 1998 Pyro Industries, Inc.

Safety Precautions Safety Notice 7 THlS STOVE MUST BE PROPERLY INSTALLED AND OPERATED IN ORDER TO PREVENT THE POSSIBILITY OF A HOUSE FIRE. PLEASE R

Detailed Safety Precautions (con t 'd) "F-. Auger - Pellet fuel is fed to the burn grate by a screw auger. This auger is driven by a high t

Pellet Fuel General Information 7 Using the UltraGrate burn system, the Whitfield Quest Plus has been designed to burn wood residue pel- lets with u

Stove Operating Controls , ?- Start Switch - The push-bunon START switch activates the convection blower ? and the combustion blower. If the exhaust

Stove Damper Settings FREESTAND STOVE DAMPER >\ The "push-pul1"damper rod is located on the lower right side of the Freestand model stov